BandMix

Connecting Musicians

SIGN UP
Blog / ,

How to Use EQ: A Musician’s Guide to Mixing with EQ

The Fundamentals of EQ

EQ (equalization) turns specific frequency ranges up or down so each sound in your mix is clear and fits with everything else. To use EQ well, clean out what a track doesn’t need, find the range where it sounds its best, and make small, purposeful boosts, always judged against the full mix rather than in solo.

This guide covers the controls and types of EQ, a frequency cheat sheet, common problem frequencies and how to fix them, how EQ and compression work together, and a step-by-step workflow you can use on your next mix.

What EQ Actually Does

Sound is vibration, and frequency is how many times per second it vibrates, measured in hertz (Hz). Low frequencies are bass; high frequencies are treble. Human hearing covers roughly 20 Hz to 20 kHz, and the top end drops gradually with age and noise exposure.

No instrument produces a single frequency. A note has a fundamental pitch plus a series of overtones (harmonics) above it, and the balance of those is what makes a guitar sound different from a piano playing the same note. EQ reshapes that balance.

In a mix, the main reason to EQ is masking: when two sounds share a frequency range, the louder one hides the other. Low frequencies are where this bites hardest, because they carry most of the energy in a typical mix and use up the most headroom. That’s why the low end needs to be cleaned up and why only a few sources (usually kick and bass) should own it.

The Three Main EQ Controls

  • Frequency: where the EQ acts. For a bell, it’s the centre of the band; for a filter or shelf, it’s the corner where the change starts.
  • Gain: how much you boost or cut, in decibels (dB). A few dB is often plenty.
  • Q (bandwidth): how wide the affected range is. A higher Q means a narrower band. Wide settings (a Q around 0.5 to 1) sound smooth and musical for tone shaping; narrow settings (around 5 and up) are for surgical cuts.

Filters also have a slope, measured in dB per octave (commonly 6, 12, 18, 24 or 48 dB/oct). A gentle slope sounds natural; a steep one removes more, more abruptly.

EQ Shapes: Filters, Shelves, Bells and Notches

High-Pass and Low-Pass Filters

A high-pass filter (also called a low cut) lets highs through and removes everything below the cutoff, which makes it ideal for clearing rumble and unneeded low end from vocals, guitars, overheads and keys. A low-pass filter (high cut) does the opposite, taming hiss or fizz above the cutoff. Use both at once and you have a band-pass filter, which leaves only the middle, as in the classic “telephone” vocal effect.

Shelves

A shelf boosts or cuts everything above (high shelf) or below (low shelf) a point by a set amount, rather than removing it completely like a filter. Shelves are great for broad moves: a little more air on a vocal, a little less weight on an acoustic guitar, or a gentle lift to the low end of a whole mix.

Bell (Peak) Bands

A bell boosts or cuts around a centre frequency, with the width set by Q. It’s the band you’ll use most for both fixing and shaping.

Notch Filters

A notch is a very narrow, deep cut used to remove one specific problem: a ringing drum, a whistling resonance or electrical hum. In Canada, as elsewhere in North America, mains hum sits at 60 Hz, often with harmonics at 120 and 180 Hz.

Types of EQ (and When to Use Each)

  • Parametric: full control of frequency, gain and Q on every band. It’s the workhorse for both cleanup and shaping, and every DAW includes one.
  • Semi-parametric: adjustable frequency and gain but a fixed Q, common on the mid bands of mixing consoles. Fast to use and often very musical.
  • Graphic: a row of fixed bands (often 10 bands, or 31 bands at one-third octave spacing) with a gain slider for each. Quick and visual, and common in live sound for tuning rooms and monitors, but too blunt for chasing one exact problem frequency.
  • Shelving and vintage-style EQs: simpler designs with a few fixed frequency choices, prized for their character. Pultec-style EQs are known for a trick of boosting and cutting at the same low frequency, which adds weight while tightening the area just above it.
  • Dynamic EQ: a band that only boosts or cuts when the signal crosses a threshold, so it can tame a harsh note or sibilance only when it happens. Many dynamic EQs can also be keyed from another track (see sidechaining below).

You’ll also see linear-phase EQs (which avoid phase shift, useful for mastering or parallel tracks, but can smear transients with “pre-ringing” on big low-frequency moves), mid/side EQs (which treat the centre and the sides of a stereo signal separately) and analog-modelled EQs (which add colour). A sensible approach: use a clean parametric EQ for corrective work, and a character EQ when you want to add tone.

Frequency Range Cheat Sheet

These ranges are approximate. They overlap, and the exact spot depends on the instrument, the key of the song and the recording, so use them as a map to start listening, not as fixed rules.

  • Sub-bass (about 20 to 60 Hz): felt more than heard; the weight of kick and sub-bass. Too much: rumble and wasted headroom. Many small speakers and earbuds barely reproduce it.
  • Bass (about 60 to 250 Hz): the fundamentals of bass and kick, plus the warmth and body of many instruments. Too much: boomy.
  • Low mids (about 250 to 500 Hz): the body of guitars, piano, snare and vocals. Too much build-up: muddy.
  • Mids (about 500 Hz to 2 kHz): the core tone of most instruments. Too much: honky or boxy. Too little: hollow and scooped.
  • Upper mids (about 2 to 5 kHz): presence, attack and intelligibility. Our ears are especially sensitive here. Too much: harsh and fatiguing.
  • Presence and brilliance (about 5 to 10 kHz): definition, consonants, cymbal detail. Too much: brittle and sibilant.
  • Air (about 10 to 20 kHz): sparkle and openness. Too much: thin or hissy.

A few common starting points: kick weight around 50 to 100 Hz and beater click around 2 to 5 kHz; snare body around 150 to 250 Hz; vocal presence around 2 to 5 kHz; and bass guitar definition somewhere around 700 Hz to 1.5 kHz, which is what helps a bass line read on small speakers.

Common Problem Frequencies and How to Fix Them

  • Rumble below about 40 to 80 Hz (traffic, handling noise, mic stand thumps): high-pass filter on any track that doesn’t need deep lows.
  • Hum at 60 Hz and its harmonics: narrow notches, or better yet, fix the grounding or cable issue at the source.
  • Mud around 200 to 500 Hz: small, wide cuts spread across several tracks usually sound better than one big cut on a single track.
  • Boxiness around 300 to 600 Hz: common on drums and vocals recorded in small rooms; try a moderate cut.
  • Honk or nasal tone around 800 Hz to 1.5 kHz: a gentle cut can open up vocals, horns and guitars.
  • Harshness around 2 to 5 kHz: distorted guitars, cymbals and strident vocals; cut gently, or use a dynamic EQ so it only acts on the loud, harsh moments.
  • Sibilance around 5 to 10 kHz: use a de-esser or dynamic EQ instead of a static cut, which would dull the whole vocal.
  • Resonances and ringing: narrow cuts at the exact frequency.

To find a resonance, boost a narrow bell by around 6 to 10 dB, sweep it slowly until the problem jumps out, then turn the boost into a cut. Use this “boost and sweep” method sparingly: a narrow boost makes almost everything sound ugly, and it’s easy to end up cutting things that weren’t problems.

Subtractive vs. Additive EQ

Most mixers cut before they boost. Removing clutter often reveals the good parts of a sound without adding anything, cuts tend to sound more natural, and they don’t eat into your headroom. A useful guideline is “narrow cuts, wide boosts.”

That doesn’t mean boosting is wrong. Adding a few dB of presence to a vocal or some low-end thump to a kick is normal, and some EQs are chosen precisely for how good their boosts sound. Just boost once the mix is cleaned up and you can actually hear whether the boost helps. Whenever you make a big change, match the output level before comparing, because louder almost always sounds “better” at first.

Leave headroom as you go. A common guideline is to keep the mix bus peaking a few dB below 0 dBFS (somewhere around -6 to -3 dBFS) so there’s room for mastering.

EQ and Compression: Which Comes First?

There’s no single correct order, but a common, practical approach is:

  • Corrective EQ before the compressor: high-pass filters and resonance cuts first, so the compressor doesn’t react to rumble or one boomy note.
  • Tonal EQ after the compressor: broad boosts go last, so the compressor doesn’t fight against them.

Many engineers use an EQ on both sides of the compressor for exactly this reason. Some compressors also have a sidechain filter, so you can stop low frequencies from driving the compression without changing the tone you hear. To compress only one part of the spectrum, a multiband compressor or dynamic EQ is now the simplest tool. And when you want to key EQ or compression from another track, that’s where sidechain compression comes in.

Creative EQ Moves

  • Filter sweeps: automate a high-pass filter rising through a build-up, or a low-pass opening up across an intro, for movement and tension.
  • Lo-fi and telephone effects: a band-pass filter on a vocal or drum loop for contrast in a verse or breakdown.
  • Section-by-section EQ: automate EQ so a guitar is fuller in a sparse verse and leaner in a busy chorus.
  • Character on groups: a gentle vintage-style EQ on a drum or vocal bus to add colour to several tracks at once.

A Practical EQ Workflow

  • Balance first. Get a rough mix with faders and panning before you touch an EQ. Many “EQ problems” turn out to be level problems.
  • High-pass where it helps. On tracks that don’t need deep lows, raise a high-pass filter until the sound starts to thin out, then back it off a little. Do it by ear rather than cutting everything at the same number, because over-filtering can make a mix sound thin.
  • Fix problems. Address mud, boxiness, harshness and resonances with small cuts.
  • Carve space between competing parts. Where two sounds clash, give each its own focus: for example, emphasize the kick’s thump and the bass’s growl in different spots, or cut a little of the guitars where the vocal’s presence lives. When cutting isn’t enough, sidechain ducking can handle the moments of overlap.
  • Enhance. Add gentle, wide boosts where a sound needs more character.
  • Check in context. Bypass each EQ at matched level, listen at moderate volume, and check on monitors, headphones and a phone or car if you can. Take breaks; tired ears make bad EQ decisions.

Your monitoring matters as much as your plugins. If you can’t hear the low end accurately, you can’t EQ it accurately, so a decent pair of studio monitors for home recording is worth the investment.

Common EQ Mistakes to Avoid

  • EQing in solo: a sound that’s perfect on its own can be wrong in the mix, and a thin-sounding guitar in solo may sit perfectly against the band.
  • Over-boosting: stacking big boosts on every track just makes everything louder and harsher.
  • Mixing with your eyes: analyzers are useful for spotting rumble or a resonance, but your ears make the final call.
  • Expecting mastering to fix it: EQ problems should be solved in the mix.

On that last point, our article They’ll Fix It in the Master: True or False? explains why. Mastering is a final polish, not a repair job, and if you’d like a professional to handle it, BandMix also offers a mastering service for your finished mixes.

Wrapping Up

Good EQ isn’t about secret settings. It’s about listening: clean up what each track doesn’t need, give every part its own space, boost with restraint and always judge in context. Keep the cheat sheet handy, trust your ears over the numbers, and your mixes will get clearer with every song.

Want to work with other musicians on your next recording? Join BandMix for free to find bandmates, producers and collaborators near you.